How to Reprogram a Skoda Key Fob
Many people wonder about how to reprogram their car key fobs, when they don't understand the reason behind why it stopped working. This is not uncommon, since key fobs can be tossed around and buttons may be damaged or jammed.
The first step is changing the battery. If this doesn't work then it may be time for the replacement.
1. Switch off the ignition.
If your key fob has stopped working in the last few days, it's likely that the battery has to be replaced. The batteries are cheap and easy to replace therefore this is the first step before attempting to reprogram the key.
Make sure the car is turned off and all doors are closed. Put your current key into the ignition and turn the switch to "On". It is not recommended to start the engine.
Press the lock button on your keyfob within five minutes. You should hear your car's locks unlock and lock to confirm your success in entering programming mode. Now you can use the key fob to lock and unlock your vehicle, and programme additional remotes. This process can also be used to reset a malfunctioning or damaged key fob. You may find it necessary to do this in the event that the key fob has been dropped over, stepped on, or exposed to water.
2. Switch on the ignition.
You'll only need a few moments to re-program key fobs in the correct way. The first thing you have to do is turn on the ignition. This will reset the system and give you a new start.
Close all your car doors. You don't need to open any doors during this procedure as it could cause the programming to be interrupted. After you have closed all the doors turn the ignition on to "On" and insert the primary key.
Press the button to lock the fob six times within 10 seconds after the engine has started. You should hear your car's lock unlocking to know that the programming mode was successful. Repeat the process for any additional remotes that you have to program. Be aware that you must program each remote as quickly as the first one, since any delay could cause it to fail.
3. Press the Lock Button
The key fob acts as an insignificant remote that can be used to lock and unlock the car. It also has the ability to use a panic key which can be used in emergencies to contact help. Your key fob might be inoperable due to a variety of reasons, including an unresponsive or damaged battery.
If the key fob in your car isn't functioning properly, you may try to reprogram it by following the steps below. This procedure is applicable to all cars, but it is crucial to follow the exact instructions in your vehicle's manual.
Start the process by turning the car on using the ignition key and not starting the engine. Press both the "unlock", "panic" and "lock" buttons at the fob for a few moments. You should hear a click, which indicates that the key fob has been successfully programmed.
4. Press the Unlock Button
To unlock and start your car, you'll have to pair a brand new key fob to it. You can do it yourself, but you'll need to know some basic information about how to program the Skoda key fob.
You'll require a long and thin tool to press the lock button inside your vehicle. A wire coat hanger is usually the best option because it's light and long.
First, open your vehicle's doors before closing them. Press the unlock button on the fob several times. This will cause your car to emit a chime, letting you know that the fob has been changed. After this you should be able the lock and unlock buttons normally. If they don't work, you will need to bring your vehicle to a dealer.
5. Press the Panic Button
The "Panic" button on your key fob is not just a handy feature that allows you to locate your car in parking garages, it's also an effective method to keep off would-be thieves. The button can trigger an alarm in your vehicle, scaring away criminals who might think you are a target for attack.
If the panic button does not work after reprogramming the key fob, it could be because the battery was not installed correctly. In this instance you'll need replace the battery of the key fob.
To do this, you need to open the key fob, and then separate the transmitter section from the key part. Remove the expired battery from the transmitter section and insert a new one with the correct orientation. Reassemble the keyfob and test its locking and unlocking features. If they don't work, you'll have to repeat the reprogramming procedure or contact a local locksmith to get help.
6. Press the Lock Button
Updated April 17, 2023: If your key fob isn't able to unlock doors, it's the time to change the button-cell battery. This tiny coin-shaped silver battery is easy to replace with the use of a screwdriver or fingernail.
When you have a new battery Follow the steps to change the programming of the key fob. Be sure to have all doors closed since leaving one open could interfere with the process. After skoda find my keys 've done this switch the ignition to 'On' but don't start the engine.
Once the key fob is programmed Press the lock button after five minutes. You should hear a sound as the car locks turn which indicates the success of the process. Repeat this process to program additional remotes to the car. If the key fob is still not working, the issue could be a wiring issue, antenna problem, software problems or a damaged circuit board. You may need to take it to a dealer to reprogramme it.